A Pipe Froze But Hasn't Burst Yet: What to Do Right Now
Quick Answer
What should you do when a pipe freezes but has not burst?
Open the affected faucet, shut off the water to that section if you can, and thaw the pipe slowly with gentle heat — a hair dryer, warm towels, or a space heater at a safe distance. Never use an open flame. As water starts moving again, check the whole run and the rooms below for leaks: a pipe that froze may have cracked, and the damage often shows up only at thaw. If you find a leak or water inside walls, shut the water off and call for help right away.
It is the coldest morning of the year so far, the kitchen faucet gives you a trickle and then nothing — and there is no water on the floor. That is actually the good version of a frozen pipe. A frozen pipe that has not burst yet is a problem you can still solve calmly. The danger window is the thaw: ice expands as it freezes, and a pipe that split under that pressure often does not leak until water starts moving again. Here is the order we walk homeowners in Pottstown, Phoenixville, King of Prussia, and across Southeastern Pennsylvania through on the phone — and the mistakes that turn a frozen pipe into a flooded room. Our prevention guide covers the longer game of how to prevent frozen pipes before winter hits; this page is for the morning it happens anyway.
First, Confirm It Is Frozen — and Find the Section
Turn on the affected faucet. A trickle or a complete stop on a bitter morning, with normal flow elsewhere in the house, points to one frozen run. Check the usual suspects first: pipes along exterior walls, in the garage, in a crawl space, under a kitchen or bathroom sink on an outside wall, and in an unheated basement corner. Look for frost on the pipe, a slight bulge, or a section that feels dramatically colder than the rest. If instead you find standing water, a spraying joint, or a rapidly spreading ceiling stain, skip ahead — that pipe has already burst, and our guide to what to do in the first hour after a pipe burst is the one you need.
Thaw It in the Right Order: A Pro Checklist
- 1. Open the faucet. Leave the affected faucet open before you apply any heat. It relieves pressure in the line and gives melting water an escape route — pressure with nowhere to go is what bursts pipes.
- 2. Shut off that section if you can. If the run has its own shutoff valve, close it. Either way, know exactly where your main shutoff is before you start, so you can stop the water in seconds if a crack opens up at thaw.
- 3. Apply gentle heat, faucet end first. Use a hair dryer on low or medium, warm towels, a space heater at a safe distance, or heat tape made for pipes. Start near the faucet and work toward the frozen section so meltwater can drain instead of building pressure behind the ice.
- 4. Warm the room, too. Open cabinet doors under sinks on exterior walls and let house heat reach the pipes. If the frozen run is in a basement or crawl space, safely raising the temperature in that space helps the whole length thaw evenly.
- 5. Watch for the moment of truth. As flow returns, walk the full length of the pipe and check the ceilings and floors below it. Drips at joints, hissing inside a wall, or a spinning water meter with everything off all mean the pipe cracked — shut the water off and call for help.
- 6. Keep checking for a few hours. Slow leaks from a thawed crack can take time to show through drywall. Recheck the area later the same day, and again the next morning.
Safety Do's and Don'ts
- Do use only gentle, indirect heat — hair dryer, warm towels, space heater at a distance, or pipe heat tape.
- Do keep the faucet open during the entire thaw and stay nearby while heaters run.
- Don't ever use an open flame — no torch, propane, or kerosene heater. Flame can ignite framing and insulation and damage the pipe itself.
- Don't pour boiling water on a frozen pipe or chip at ice with a tool; both can crack the pipe you are trying to save.
- Don't ignore water that got into walls, ceilings, or insulation after a thaw leak. Hidden moisture is exactly how a plumbing problem becomes a mold problem — our water damage restoration and mold testing teams handle that second stage.
Frequently Asked Questions
The classic signs are a faucet that slows to a trickle or stops completely on a very cold morning, frost on an exposed section of pipe, an unusual bulge in the pipe, and odd smells from a drain. Pipes along exterior walls, in crawl spaces, garages, and unheated basements freeze first. If water still flows normally everywhere else in the house, the freeze is usually in one exposed run — and if there is no water on the floor yet, you still have time to act before it bursts.
If you can find the shutoff for that section, yes — closing it takes pressure off the frozen area, so if the pipe has already cracked, far less water escapes when it thaws. At minimum, know where your main shutoff is before you start thawing. Open the affected faucet and leave it open while you work: it relieves pressure and lets you see the moment water starts moving again.
Work slowly with gentle, indirect heat. A hair dryer on a low or medium setting, a portable space heater placed at a safe distance, warm (not hot) towels wrapped around the pipe, or thermostatically controlled heat tape made for pipes are the safe options. Start closer to the faucet and work back toward the frozen section so melting water has somewhere to go. Keep the faucet open and check every few minutes for leaks as flow returns.
Never use an open flame — no blowtorch, propane heater, kerosene heater, or charcoal device. Open flame can ignite nearby framing and insulation, damage the pipe itself, and create a carbon monoxide risk. Never pour boiling water directly on a frozen pipe, never leave a space heater unattended, and never keep thawing if you see water spraying, hear hissing inside a wall, or notice the water meter spinning with all faucets off — shut the water off and call for help instead.
Watch and listen as it thaws. A cracked pipe often reveals itself only when water starts moving again: dripping or spraying at a joint, water stains spreading on a ceiling or wall, a sudden drop in pressure, or damp flooring near the run. After flow returns, check the full length of the pipe and the rooms below it over the next few hours. If you find a leak — or water got into walls, ceilings, or insulation — shut the water off and call a restoration professional, because hidden moisture left in wall cavities can grow mold within days.
Thawed the pipe and found a leak — or water where it should not be?
My Water Damage Hero is a local, family-owned company based in Pottstown, PA. We offer free visual inspections, work with insurance companies, have an industrial hygienist on staff, and respond 24/7 across Montgomery, Chester, Delaware, Bucks, Berks, Philadelphia, Lehigh, Lancaster & Monroe County, PA.